I forgot about formatting it. The recommendation is to align partitions to 2048 sectors. Balao / September 2, 2004 10:51 PM PDT In reply to: Install old hard drive as slave drive? by Eduardo A. weblink
Cher Reply Kieron says: August 22, 2007 at 11:25 am How do I set up a slave hard drive in windows without formatting it as I have information on it. by JCHJCH / September 3, 2004 2:08 AM PDT In reply to: Install old hard drive as slave drive? Read it before posting http://www.catb.org/esr/faqs/smart-questions.htmlRuby gems repository done right https://bbs.archlinux.org/viewtopic.php?id=182729 Offline #13 2014-08-11 02:35:51 matierpixel Member Registered: 2014-08-10 Posts: 19 Re: [SOLVED?]Install Arch onto a second hard drive....with Syslinux anatolik wrote:matierpixel I HAVE ALWAYS USED THE SLAVE HARD DRIVE AS THE BACKUP DRIVE THUS THERE IS NO WEAR AND TEAR PLACED ONTO THE OLDER DRIVE ON A DAY TO DAY BASIS.
Otherwise I would have to get an IDE drive because I do have an extra IDE port. arch-chroot into your Arch installation and reinstall syslinux. In Windows terms, you might think of a partition as a single drive letter (like C: or D:). I'm confused too.
Not having that available when I have been at their house tutoring has often been a problem. Don't force it. You first say you do not even get to the syslinux menu, but then you describe the outcome of both options, each of which must be selected from the syslinux menu. What Needs To Be Done To The Hard Drive Once Installed Hope you can help, so far this has been a longwinded exploraton of my computer.
It is registering in the bios and everything but I can#t format it since the drive letter doesn't exhist. Offline #2 2014-08-10 19:03:25 jasonwryan Anarchist From: .nz Registered: 2009-05-09 Posts: 20,655 Website Re: [SOLVED?]Install Arch onto a second hard drive....with Syslinux https://wiki.archlinux.org/index.php/Sy … ther_drive Arch + dwm • Mercurial repos Okay, I've changed the boot order but I don't know what to do next?. Next Step?
I need help though please help me. What Kind Of Power Connector Does A Floppy Disk Drive Typically Use Things have changed a bit since then, mostly for the better I think. UK immigration officer made a mistake. I bought an Uber Chakra case and a WD Caviar Blue Hard Drive.
When it runs a self test the drive is detected but only when I press f1 to enter setup and then it will not enter setup. I only have 2 SATA ports on my motherboard. There Are Two Tasks That Need To Be Done With A Hard Drive Before The Operating System Can Use It. I have it hooked up and it is recognized in the bios but it does not show up in my computer. What Needs To Be Done After Installing A Secondary Hard Drive Either way we should have free space to work with.
You may want to choose automatic login. http://textminingnews.com/hard-drive/any-reviews-on-wd-3-tb-usb-3-0-ext-hard-drive.php Minimum system requirements for Xubuntu would fall roughly between Ubuntu Server and Desktop: 512 MiB of system memory (RAM)5 GB of disk spaceGraphics card and monitor capable of 800x600 resolutionWith Lubuntu, Reply Geoffrey says: January 5, 2009 at 10:25 am This guide helps even those who are good at computers. Reply Tyler Thompson says: September 10, 2007 at 2:10 pm David, When you clone a drive, it copies it exactly as it were before. What To Do After Installing A Second Hard Drive
If I'm replacing my hard drive I understand that in order to clone the hard drive I need to have the new hard drive act as the slave drive which I Reply ian says: December 26, 2008 at 2:19 am hi, nice step by step, but can you tell me how can i locate the slave hard drive when it is not Advanced Search Forum Hardware Desktop Computer Hardware Newbie need help installing second Hard drive If this is your first visit, be sure to check out the FAQ by clicking the link http://textminingnews.com/hard-drive/anything-i-need-to-know-when-buying-new-hard-drive.php It makes sense to me to "recycle" any usable components that still are good, as long as the computer case has room for the extra drive.
Reply John Oliver says: May 23, 2008 at 4:02 pm Excellent article. What Is A Risk Or An Effect Of Software Piracy Tyler Thompson PCMechanic Editor-in-Chief [email protected] Reply steve scott says: November 6, 2007 at 4:09 pm hi i am having trouble installing my new sata harddrive i have pluged it in and I did need to explore a little after using the wizard to find I had to right click on the new driver in the manager window to start the formating process
If you did not use a controller card, enter the BIOS (usually by pressing the F1, F2, F10, F12, or Delete key when you see the Power-On Self-Test or the manufacturer Saved me a lot of ‘messing about' time. Putting it as a slave, is a good use for backup stuff. You Want To Install An Ssd Drive In Your Desktop Computer But The Drive Is Far Too Narrow To Fit So no, thanks. –Oleh Prypin Jan 9 '13 at 11:03 A very complex answer indeed!
It's a great help if you get into troubles.Kees Flag Permalink This was helpful (0) Collapse - Many thanks to Kee, remusson and rhbass by grandpaw7 / August 26, 2004 11:16 by Greatfuldead101 / September 3, 2004 1:29 AM PDT In reply to: Re: Install old hard drive as slave drive? However, I was unaware that the "Old Drive" was infected with a virus. http://textminingnews.com/hard-drive/any-ideas-for-old-hard-drive.php Reply Bomberboy92 says: August 25, 2007 at 11:25 pm Wow thanks this tutorial really helped me with my new drive.
They might even come with a 160 gig or above HD. THANKS! Any suggestions? Offline #8 2014-08-11 00:38:23 Trilby Forum Moderator From: Massachusetts, USA Registered: 2011-11-29 Posts: 15,236 Website Re: [SOLVED?]Install Arch onto a second hard drive....with Syslinux matierpixel wrote:Unfortunately, no.
For most home users who don't play every 3D game on the market it will very hard to fill up a 40 gig HD in 3-5 years worth of use. If your drive is particularly old, this is probably the case. In addition I had to purchase a PCI serial ATA host controller card with a cable to connect the new HD.