Home > Hard Drive > An Attempt To Master+slave A Harddrive

An Attempt To Master+slave A Harddrive

Contents

One problem though - after setting up the new drive and using Norton Ghost 10.0 to clone the old drive, I can't boot from the new drive. I'll make my drive master and boot from it letting my boot manager load. I have secondary machine that it running win 98… I'm working on getting drivers for my WD 250 gig EXHD. Should I try Cable select? have a peek here

If installed and works as master, ghost the image to the network. Pye May 23, 2007 7:18 pm Reply # Ok-I am not a tech, but do both the slave and master drive have to have the same operating system? SSDs aren’t subject to the same pitfalls of hard disk failure simply because there are no moving parts within the SSD. You can try taking control of the folder or use recovery software like Recover It All to copy the files off which will strip off the permissions.

How To Slave A Sata Hard Drive

What I did state was that it was intended more for individuals who were already computer savy. Does he need an actual Windows Vista disk instead of the ones you make when you first get the computer? Hard drive shows up as slave rather than master and system won't boot. If not, then reboot off the diskette and scan the drive for errors.

And your little guide here solved my problem. Well, I'm kind of new to this, but I'll throw my hat in the ring. Feel free to call me direct 727-345-9665 if you have any questions. Master Slave Hard Drive Setup Reformatted and back online the next day.

Reply Andrew Harward says: October 5, 2007 at 9:26 pm Before trashing your broken drive, it's a good idea to check whether it's still under warranty, as most manufacturers provide at How To Slave A Hard Drive I would next cold boot to a virus scan diskette and verify the hard drive could be accessed and free of viruses. You could also Network the machines together and do the transfer that way. Disk Management is located in the Computer Management part of the Administrative Tools control panel.

Step 4: We are going to need to remove the screws from the front and then go around the back of the pc and remove the screws on that side also. How To Slave A Laptop Hard Drive Dave June 20, 2008 10:37 am Reply # PS: Follow up to previous post: If your drive is recognized in disk management you can use data recovery software to pull the Only cowards work with a backup!!!! Reply Kallon says: July 13, 2014 at 5:28 pm I know this is a while from original comment but couldnt you just remove the other hard drives and make the one

How To Slave A Hard Drive

Addt'l drive install I have this exact same issue when I attempt to replace the original 80gb C-drive in my Sony Vaio PCV-RX650 with a new Western Digital 500 gb Caviar http://www.tomshardware.com/forum/285281-30-hard-drive-resgisters-slave Clear and accurate, thanks heaps! How To Slave A Sata Hard Drive Thank you and I hope you get your issues resolved! How To Install A Second Sata Hard Drive DTI Data Recovery January 4, 2008 12:27 pm Reply # Perla, Yes this post shows how to slave a hard drive so that you can either copy data off, or if

But I would seriously consider getting a new motherboard when budget allows. Dyan Reply Dyan says: December 29, 2007 at 11:32 am Joshcore, can you reply me. Chances are that you don't need to worry about this. I have made it a slave drive. How To Slave A Hard Drive To Recover Data

An "Invalid Drive Type" error usually means that the wrong drive type has been selected in CMOS. Reply Catalin says: May 31, 2010 at 1:29 am Also my laptop was working fine….. Windows will identify any sectors that have gone bad. You are going to want to try and push, any cables in the way of the rear of the drive, up and out of the way.

It doesn't have an external power source but seems to just turn off randomly or go to sleep which worries me. Slave Hard Drive Definition The hard drive that the system boots from is usually the primary master. other then that its not able to without this the drive will not read and be able to transfer files Reply Gary Hart says: August 7, 2007 at 4:46 am Thanks

The W2K also detected the new drive when I try check in the ‘device manager'.

cable select. The computer is restarted and goes into the scheduled disk check. Can i add that the wizard does not pop up automatically. How To Install A Second Hard Drive Windows 10 I originally bought my NO NAME computor from him back in December It first went down in March probally from trying to download free music off Kazzaa.

But since IDE/EIDE is perhaps the popular and most used drive, I am going to assume that is the drive. After this, I would check with tech support, because I would not want to overlook something that could help me avoid reloading her original hard drive, as quite a few users It has SSC_DIS, PM2, OPT1, & OPT2. Thanks for the help.

Get an identical Hard Drive and swap out the Logic Unit (Electronic Board). With these things, it’s always a process of elimination. i don't want to reformat the HDD. The origianl post and answers to other questions are great!

By the fifth sentence, ‘Serial ATA'. Proffitt Forum moderator / September 12, 2016 4:57 PM PDT In reply to: not booting up Set for a slave and there is none, or the BIOS is set for a Will Smtih December 22, 2007 8:50 pm Reply # Very useful information.